News

Location: Home  /  News  /  Corporate News
The differences between threaded valves, threaded flange valves and welded flange valves
Date:2026-07-21 12:00:00 Author:Zhejiang Yonghao Valve Co., Ltd.

I. Principle Differences in Connection Structures


Threaded Valves


The valve body has external or internal threads machined at the inlet and outlet ends. It relies on the matching internal and external threads of the pipeline to achieve threaded sealing without a flange disc component. It belongs to the direct connection type with threads.


Threaded Flange Valves


The valve body itself has a flange disc. The inner hole of the flange is machined with threads. The end of the pipeline is equipped with an external threaded short pipe that is screwed into the flange's threaded hole to achieve pre-fixation. Then, the flange gasket and bolts are used to lock the flange end face to achieve sealing. It has dual structural features of threaded assembly and flange compression.


Welded Flange Valves


The valve body is cast or forged with a flange disc. There are no built-in threads on the flange. The end of the pipeline is processed with a bevel, and the pipe section is welded to the flange using对接 welding or corner welding techniques to form a rigid whole. The sealing is achieved by pressing the flange gasket with bolts, and the connection has no threaded pair structure.


II. Assembly and Disassembly Characteristics


Threaded Valves: Assembly only requires rotating the threads with a pipe wrench to complete. Disassembly is convenient; multiple disassemblies can cause thread slippage and sealing packing failure, resulting in a significant decline in the reliability of repeated use.


Threaded Flange Valves: First, the threads are pre-connected to the pipeline, then the bolts are tightened on the flange. Disassembly requires loosening the flange bolts and then unscrewing the threaded pipe section. The disassembly process is more complex than that of pure threaded valves, and the risk of thread wear is lower than that of ordinary threaded valves.


Welded Flange Valves: The pipeline and flange are permanently welded together. Under normal operating conditions, they cannot be disassembled without damage; for maintenance, the pipeline needs to be cut to remove the valve, and after the maintenance, it needs to be re-welded and inspected. The disassembly process is complex and irreversible.


III. Applicable Operating Conditions and Parameters


Threaded Valves: The nominal diameter ranges from DN15 to DN50, suitable for low-pressure and normal-temperature media; they are mostly used in water supply and drainage, low-pressure gas, and small branch pipelines. They are not suitable for high-temperature, high-pressure, and highly-vibratory pipelines.


Threaded Flange Valves: The nominal diameter ranges from DN15 to DN100. They have better pressure-bearing and temperature resistance than pure threaded valves; they are suitable for small-diameter, regular maintenance but without welding construction conditions in process branch pipelines. They are suitable for general medium-pressure scenarios.


Welded Flange Valves: The full range of diameters is covered. They are suitable for high-pressure, high-temperature, flammable and explosive, and highly-vibratory process pipelines; they are mostly used in chemical, heating, and oil and gas main pipelines. The connection is strong, and the ability to resist pressure difference, deformation, and vibration is the best. The probability of medium leakage is the lowest.


IV. Sealing and Structural Reliability


Threaded Valves: Sealing relies on the winding of sealing materials such as tape and hemp, and the threaded gap is prone to leakage hazards. The threaded seal is prone to loosening and leakage under pipeline vibration.


Threaded Flange Valves: The threads only serve as pipeline positioning. The main sealing is borne by the flange gasket. The threads do not bear the sealing pressure of the medium. The leakage risk is significantly reduced, and the seismic performance is better than that of pure threaded valves.


Welded Flange Valves: Welding eliminates the gap between the pipeline and the flange, and the overall structure has no movable threaded pair. The flange end face gasket independently bears the sealing. The anti-pressure difference, anti-deformation, and anti-vibration performance is the best, and the probability of medium leakage is the lowest.


V. Construction and Acceptance Requirements


Threaded Valves: Construction only requires thread processing and sealing material winding, no hot work operations are required, and acceptance only checks the thread sealing performance;


Threaded Flange Valves: The pipeline threads need to be machined, the flanges need to be aligned, and bolts need to be evenly tightened diagonally without mandatory hot work procedures;


Welded Flange Valves: Construction includes pipe beveling, welding, non-destructive testing of welds, and correction of flange parallelism. It is a hot work operation, and acceptance needs to add weld inspection items.


VI. Summary of Core Characteristics


Threaded Valves: No flange, direct threaded connection, small-diameter, low-pressure, no welding, easy to disassemble and assemble, average sealing performance;


Threaded Flange Valves: With flange, threaded positioning + flange sealing, small-diameter, medium-low pressure, no welding, convenient for maintenance;


Welded Flange Valves: With flange, welded rigid connection, full range of diameters for high-pressure, high-temperature, flammable and explosive, high-vibration process pipelines; the connection is strong, and the sealing reliability is the highest.


Home
Products
Contact